---
description: Dating > Hot tub hook up kit
---

# Hot tub hook up kit

**Click here:** \
&#x20;\
&#x20;※ [**Hot tub hook up kit**](http://nyamituclay.hotelsvr.ru/?dt\&keyword=hot+tub+hook+up+kit\&source=gitbook.com5_dating_poster) \
&#x20;\
&#x20;※ [**♥ Hot tub hook up kit**](http://nyamituclay.hotelsvr.ru/?dt\&keyword=hot+tub+hook+up+kit\&source=gitbook.com5_dating_poster) \
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\
&#x20;\


Preparing the Site Most hot tub owners chose to install their new hot tubs outdoors. I used the switched leg of the 220 circuit to power the extra pump. For this reason, you will need a firm foundation on which the hot tub can rest. When you are done, you should have one of each color for the length between the main panel and the spa pack and also the length from the spa pack to the hot tub.\
&#x20;![hot tub hook up kit](http://i.ebayimg.com/images/i/390663047900-0-1/s-l1000.jpg)\


Step 2: Gather Materials Gather all of the prime materials and equipment before you go about installing your spa. Tank water heaters have a tube on one side that leads the cold water to the bottom of the tank. Your electrician may also need PVC cement and electrical tape. So I decieded it was solo for it to go. But 5 feet of length seems sufficient. Hello Thanks for the comments. And because the potential dangers involved with wiring a hot tub may give most homeowners pause, there is quite a market for qualified contractors. Only use this method if your la air system works well and the valves close properly.

Proceed to Step 3 and create the Hartford Loop. Flexible Connections Listed packaged spa or hot tub equipment assemblies or self-contained spas or hot tubs are permitted to use flexible connections as follows: flexible conduit, liquid-tight flexible metal conduit or liquid-tight flexible nonmetallic conduit no more than six feet long, cord-and-plug connections, and cord-and-plug connections with a GFCI-protected cord that is no more than 15 feet. Know the NEC Hot Tub Electrical Code Electricians and contractors need to read and understand the National Electric Code NEC , especially the sections pertaining to hot tubs. Many older homes built before 1970 supplied electricity through panels rated below 100 amps.\
&#x20;![hot tub hook up kit](https://i1.wp.com/acc-spas.com/page/wp-content/uploads/2015/07/smtd2000.jpg)\


**Installing Hot Tub Ozonators** - The wiring can cost several hundred dollars in parts, plus conduit and fittings. Problem is the sensor seems to of failed in the control panel.\
&#x20;![hot tub hook up kit](https://i.stack.imgur.com/J6zAS.jpg)\


Choose a location for your hot tub. Make sure the spot you choose is large enough for the hot tub as well as some extra leeway for getting in and out and performing maintenance. A safe amount to allot is approximately 10 feet 3. Many codes require at least 5 feet 1. The hot tub should be at least 10 feet 3 m away from any overhead power lines, as well as 5 feet 1. Water and electricity do not mix. Prep the site, if necessary. Hot tubs, when full, can weigh as much as 3,000 pounds 1,361 kg. For this reason, you will need a firm foundation on which the hot tub can rest. If you don't have a firm foundation, you risk damaging the tub voiding any warranty it comes with. Concrete provides a very strong foundation. At the same time, it may not be aesthetically pleasing and will be permanently anchored into place if you ever choose to move the hot tub. These pads have interlocking grids that make installation easy, and they can be removed if you ever decide to relocate your tub. At the same time, spa pads may be less supportive than concrete. Make sure you have a solid base to work with, and you choose the strongest pads if you use this option. Call a general contractor if you decide to place your tub on a deck or to accommodate the tub. If you want to place your tub onto a deck, check first with a contractor. They should be uniquely suited to tell you whether the deck will be able to withstand a ton or more of weight bearing down on it like a continuous hammer. The last thing you want to have happen is to break your deck, and then your tub, upon installation. Create a route for the power to reach the hot tub. Most modern tubs are self-contained, meaning you won't have to run any plumbing in order to get the tub up and running. But electrical wiring is another matter. Cities usually have codes for using certain types of conduits, so make sure you talk with your local building department. When you have, decide if you'd like the conduit to run under or above ground. A 240V, 50-amp GFCI Ground Fault Circuit Interrupter should be sufficient on many tubs. Multiple-pump tubs may require a 60-amp circuit. If you don't have familiarity wiring this kind of circuit, it's best to call an electrician to do it for you. Plan your delivery route of the tub from the curb to the foundation. An unfilled hot tub can weigh upwards of 800 pounds 363 kg , so it's important to know how you will get it from the delivery van to your backyard. Make sure that the width of the tub will pass through any gates, foliage, or structures with enough leeway. Cutting a branch or removing a part of a fence, although it appears drastic, is sometimes the only thing that you can do. Assemble the hot tub and hook up the electricity. The voltage of a hot tub is higher usually around 240 volts than regular home outlets, so you will need to install a breaker to your electrical control box. If you are not familiar with electrical systems, it is best to hire an electrician to assist you in this aspect of installation. See the section below for more information on electrical wiring and help. Prepare the hot tub for use. You're almost ready to start enjoying your brand new tub, without having broken the bank by paying someone else to install it. No special water is necessarily required. If wiring on your own, make sure your specs are right. Again, if there is any doubt about how to wire the circuit responsible for the hot tub, use a licensed electrician. The maximum current draw should also play a role in determining wire size. In fact, all wiring should be copper; aluminum wire should be avoided. Then, reduce the wire to short lengths of 6 10mm 2 in between the junction box and the hot tub.
